What model BendPak is that exactly? And round about what was the install cost? Did BendPak help you find the installer. Thanks
av8ndoc it’s a HD-9, on the Bendpak website there is a page that helps you locate an installer. Make sure you inspect the lift when it’s delivered because they often ship scratched units.
Pretty sure this doesn't meet their installation requirements of 3' clearance all the way around it.
Allen Cunningham Interesting they’ve actually seen this video and photos of the installation and didn’t say anything.
By any chance, do you live in the DMV and did SGS install your lift?
GiuseppeM I thought I recognized those guys. They just installed a lift in my dads garage yesterday
David Sethian Yes that’s him
estos es que en pesaron la casa por el tejado son malos montando elevadores
ramps are sticking out of the garage..glad you didnt mount it
Is this a joke?
1963 Corvette Grand ???
Bendpak says to use a forklift or crane to position the cross tubes into position. That's simply ridiculous. I'm planning on installing mine by laying the posts down and sliding the cross tubes in just like you did.
What state are you in and who did the install
I got nervous every time someone walked close to the GT3 with a piece of metal....
Great video. Recently had a garage build with 10' walls with this in mind. What did you coat your garage floor with? Thx.
Craig Olson I bought an epoxy paint for garage floors at Home Depot, I didn't put the color chips in it though
Hello GiuseppeM: Did I see that you used a 110v outlet for power? The spec shows 220 so I was wondering how you powered it. Thanks....
Great, thanks for the info. The drywall in my new garage was hung today so I am getting close to ordering. i went ahead and ran 220 before drywall started about 9 feet up so that i could swing power overhead and not have to worry about cords. Appreciate you posting this video.
Todd B hello, they sell 2 motors, 120V and 220V, the 220V is a little faster but I'm happy with 120, is fast enough.
What's your recommend ceiling height if you want to get a 4 post lift that can fit one car on top and obviously one car below (let's say a normal sedan and a sports car on top) ?And is the high raise garage door motors required?Thanks in advance, love the video.
HKMediaChicago 9.5' would be the minimum height which is what I have. For a large sedan underneath I would say 10' is required.
HKMediaChicago I'm not sure, I have 11' ceilings and the high rise motors but if you go on the BendPak website there should be a page that can help you
How long did it actually take?
drmarc83 around 8 hours
obviously, it doesn't work since you didn't lift the car in the end.
So its not mounted to the ground?...
Wacky Ninja no it's free standing and can roll on casters, or you can bolt it down
do you anchor it in place? or it seems very safe without the anchors in the floor? I am looking to get one of these but don't want to drill in the concrete
Power Jack Repair it's not anchored and it's not required, I bought the casters so I can move it if needed
pickup actually sounds strongry gpod other .
how do you close the door..
With the button 😂
what size of garage is that and ceiling hight
It's a 25'x30'x14' with high raise garage door motors
Nice. Had a couple of questions if you dont mind. 1) How long did it take altogether?2) Although the likelihood is small, how easy is it to somewhat disassemble it to move to like the side of your garage, if need be?
guys I bought one too and I had them drop it at shipping center. I rented a 26' uhaul and 4 buddies and I moved it into my garage. If you do not have a engine hoist at all it will take atleast 4 guys.
+otm646 yes Bendpak either ships straight to them or to the closest hub and the installer picks it up (they had a rolling bed to unload it on my driveway)
Did you have the install guys take care of transportation to your location?
+John Lai oh no that's a full job to take it apart, also like I said you couldn't lift the runways
Hi Giuseppe. Sorry, let me clarify. I believe the casters let you move it around in the current rectangular form only, right? My question was more around, if you had to move all the four posts and ramp against the wall, could you do that easily? How much did installation run?Thanks!
Thank you I watched your videos many times! Check out my house construction timelapse when you get a chance you may like it!